AUTONET TV

Some New Boots (Suspension Maintenance)

There are some boots that don't come in a shoe box and aren't worn on your feet.  They are called axle or CV boots, and they can be important parts for many vehicles.

That CV stands for constant velocity.  CV axles are mainly used in front-wheel drive and all-wheel drive vehicles. They're also used in some rear-wheel drive vehicles with independent suspensions.  They have two CV joints, one inner and one outer, placed between the axle and the drive wheels.  That way the vehicle's engine power can drive the wheels, no matter what angle they are.  They also adjust for the different speeds wheels turn as they go around corners. 

Because roads are full of all sorts of hazards (dirt, oil, water, grime), these CV joints need to be protected.  They also have grease in them to keep the bearings moving smoothly.  That's the job of the rubber boots that are supposed to keep that debris out.  These CV or axle boots are made of rubber or plastic and usually last a long time without any problem.  But sometimes they fail, either from being hit by debris or age causing the rubber or plastic to deteriorate.  That can allow the grease to leak out of the joint and the moisture to get in.  And that's where the trouble is.

So it's important to have a vehicle's CV boots checked periodically, especially when they begin to have more than 100,000 miles/160,000 kilometers on them.  A technician inspects them for tears or cracks.  Sometimes if the problems are found early enough, the boots can be replaced and the joints can be re-packed with grease. 

But sometimes the CV joint can wear out even though the boot is intact.  When the CV joint fails, you might hear a grinding, humming or clicking noise and feel vibration.

Some of these can be difficult to access for service, so many service advisors will recommend replacing the joints and boots at the same time.  Just remember, new CV boots won't make a fashion statement, but they will keep your vehicle going down the road for years to come.

S T Foreign Auto Service
415 E Brighton Ave.
Syracuse, NY 13210
315-478-2161
http://www.stforeignauto.com

The S T Foreign Auto Service Basic Guide To Synthetic Oil

Synthetic motor oil has been around for a long time, and more and more new vehicles are leaving factories with synthetic in their engines. But a lot of drivers don't really know much about it.

Let's start with conventional oil – the kind folks are used to. Conventional oil is made up of naturally occurring hydrocarbon chains, which means its molecules are long and have various lengths. Like a pile of pencils, some of them new and some of them used.

Synthetic oil is man-made. Its molecules are more uniform and regular in shape – more similar to marbles than pencils. Some synthetic oil starts with a petroleum base that's modified and others are entirely synthesized from other materials.

Synthetic motor oil works better in both hot and cold temperatures. It's more chemically stable so it doesn't readily evaporate or break down in the high heat produced inside your vehicle engine. This means it resists turning to sludge, which is a real engine killer.

Remember that marbles and pencils thing we were talking about? Well, that makes synthetic oil slipperier than conventional oil which means less friction in your engine. Your vehicle engine runs cooler, wears less and lasts longer. You also get a boost in power and maybe even an improvement in fuel economy.

Synthetic oil also lasts longer so you change it less often – which is great for the environment. With longer oil change intervals, you need an oil filter specifically built for the longer service life of synthetic oil. Talk with your friendly and knowledgeable S T Foreign Auto Service service adviser about synthetic oil and synthetic blends – they might be just what you need to improve engine performance and extend the life of your vehicle.

Give us a call.

Slippery When Wet (Driving on Wet Leaves)

When the leaves fall, you might take a sightseeing trip to see them at peak color.  Or you may simply live in a spot where there are a lot of trees.  When those leaves get wet, you'd be surprised to learn just how slippery they can be. 

We all know ice is slippery to drive on.  What causes tires to slip on ice is a thin layer of water that comes between the road and your tires.  Wet leaves can have the same effect.  The surfaces of leaves are super slick when they're dry, even worse when you add a little moisture.  There's one other thing about leaves.  They are smaller than each tire's footprint, so your tread grips the pavement with uneven traction.

One study showed that your stopping distance can more than double on a surface covered with wet leaves when compared to that same road when it's dry.  Double! That can spell trouble.  So if you find yourself heading into an area with wet leaves on the road, slow down before you get into a jam.  If you do start skidding, use the same driving techniques as you would on ice.  Let off the accelerator, resist jamming on the brakes and steer into the skid.  Again, speed can get you into trouble fast on a slippery surface.

One thing that can help is having tires that are appropriate for the way you drive and the places you travel.  Your service advisor can offer suggestions for tires that are right for you.  Have a technician examine your tread depth and the condition of your tires' rubber.  Sun can break down rubber over time, and age can cause tires to fail, even if their tread seems to be deep enough. 

Your tire is the point of traction between your vehicle and the road.  Uncontrolled skids spell trouble and danger.  Slow down when you see wet leaves on the road.  They can make traction disappear before you know it.

S T Foreign Auto Service
415 E Brighton Ave.
Syracuse, NY 13210
315-478-2161
http://www.stforeignauto.com